The design method of active filter can be roughly classified into two categories: cascade method and analog method.
Cascade method
According to the requirements of technical indicators, find out the transfer function that can be physically realized (usually from the ready-made active filter materials and manuals), and decompose it into the product of low-order functions (mainly second-order functions). The low-order functions are realized by active circuits and then cascaded together to realize the original transfer function. Circuits that implement low-order functions are generally called basic sections, and there are many typical second-order basic section circuits for designers to choose from. According to the number of amplifiers used in the basic section, it can be divided into single-amplifier circuit, double-amplifier circuit, three-amplifier circuit, and four-amplifier circuit. Figure 1 shows several basic section examples. The cascade method design process is relatively simple, the circuit characteristic adjustment is easy, the realized circuit is relatively economical, it is a commonly used method.
Simulation method
First design the LC filter that can meet the technical index requirements as a design prototype, and then use the active circuit to simulate the realization. This method can be divided into component simulation method and functional simulation method, and the prototype is mostly based on the LC ladder type filter with double-terminal termination resistor. Generally, the analog method requires more components than the cascade method.
Active filter design stepsWhen designing an active filter, generally follow the following design steps.
1. Design of transfer function
According to the requirements of the filter characteristics, design a certain type of n-order transfer function, which can be decomposed into several low-order (such as first-order, second-order or third-order) transfer function product form.
When designing low-pass, high-pass, band-pass, and band-stop filters, the frequency normalization method is usually used, and the low-pass prototype transfer function is first designed. If you need to design a low-pass filter, you can transform the low-pass prototype transfer function into a low-pass target transfer function: if you need to design a high-pass filter, you can transform the number passed by the low-pass prototype into a high-pass target transfer function; if you need to design In the case of a band-pass filter, the low-pass prototype transfer function can be transformed into a band-pass target transfer function; if the design of a band-stop filter is required, the number passed by the low-pass prototype can be transformed into a band-stop target transfer function.
2. Circuit design
According to the design requirements of each low-order transfer function, design and calculate the basic section of the active filter circuit. First select the circuit form, and then design and calculate the corresponding component parameter values ​​according to the designed transfer function. According to the design requirements, specific requirements are put forward for each circuit component.
3. Circuit assembly and debugging
Design and assemble each low-order filter circuit first, and then cascade each low-order circuit to form the entire filter circuit. Then carry on the corresponding adjustment and performance test to the whole filter circuit, and examine the design result.
Active filter design exampleDesign a low-pass filter circuit, requiring its cut-off frequency F0 to be 10 kHz, Q=0.707, passband gain H=10, f is far greater than fo, the attenuation rate is not less than 40dB/10 frequency band, cutoff frequency and gain The error of etc. is required to be within ±10%.
1. First select the circuit form, and determine the order n of the filter according to the design requirements.
(1) From the attenuation rate requirement -20xndB/decade frequency≥40dB/decade frequency range, calculate n=2
(2) According to the requirements of the subject, choose the infinite gain multiple feedback low-pass active filter circuit form.
2. Design the specific values ​​of the corresponding components in the circuit according to the requirements of the transfer function.
(1) Select the value of capacitor C and resistor R according to the characteristic frequency fo of the filter.
The size of the capacitor C generally does not exceed 1uF, and the value of the resistance R is in the order of kQ. Table 1 provides the reference comparison table for the selection of cut-off frequency fo and capacitance value.
(1) Select C2, set the value of capacitor C2 to 1 nanofarad, and get the values ​​of C1, R1, R2, and R3.
3. If there is a sensitivity requirement, further limit the error and stability of the component parameter value according to the sensitivity.
Managed POE Industrial Switches
The POE switch port supports an output power of 15.4W or 30W, in line with the IEEE802.3af/802.3at standard, and supplies power to standard POE terminal equipment through network cable power supply, eliminating the need for additional power wiring. In line with IEEE802.3at POE switch, the port output power can reach 30W, and the power available to the powered device is 25.4W. In layman's terms, a POE switch is a switch that supports network cable power supply. It can not only realize the data transmission function of ordinary switches, but also at the same time. Supply power to the network terminal.
POE (Power Over Ethernet) refers to the use of IP-based terminals (such as IP phones, wireless LAN access points AP, network cameras) without any changes to the existing Ethernet Cat.5 cabling infrastructure. Etc.) While transmitting data signals, it can also provide DC power supply technology for such devices. POE technology can ensure the normal operation of the existing network while ensuring the safety of the existing structured cabling, minimizing costs.
POE is also known as a local area network-based power supply system (POL, Power over LAN) or Active Ethernet (Active Ethernet), sometimes also referred to as Power over Ethernet for short. This is the use of existing standard Ethernet transmission cables to transmit data and data at the same time. The latest standard specification of electric power, and maintains compatibility with existing Ethernet systems and users. The IEEE 802.3af standard is a new standard based on the POE of the Ethernet power supply system. It adds related standards for direct power supply through the network cable on the basis of IEEE 802.3. It is an extension of the existing Ethernet standard and the first international standard for power distribution. standard.
Poe Ethernet Switch,2 Port Network Switch,Managed Poe Industrial Switches,Industrial Poe Ethernet Switch
Shenzhen Scodeno Technology Co.,Ltd , https://www.scodenonet.com