Fortunately, I got a MasterBox Lite 5, as a novice, writing content with subjectivity, please dashes pat.
First of all, let's take a look at the chassis data given by the official:
From the above it can be seen that the size of the chassis is quite large and the individual feels longer than the average mid-tower chassis.
With excitement, I finally received a long-awaited “Rui†on a hot afternoon.
The packaging is very tight, cardboard frame with the carton out of the box:
Look at my original chassis.
Personally still quite like, look good, right?
But the fly in the ointment is because the cabinet is small and can only be air-cooled at a height of 13cm or less. For me, who likes to blow 12cm on a large fan side, I can't stand it. I had to go to 120 to cool it. After the water cooled, it was discovered. . . . . . . . Still can't get up, there's not so much room inside! The ultimate smart scheme:
In the cold exhaust, fans are added outside the chassis. . .
so awkward
Appearance Gallery
Personal experience with the appearance and details of the chassis:
The overall workmanship of the chassis is rigorous. The combination between the boards is tight, and the internal space is particularly large. Although the parameters do not support E-ATX, the personal feeling space is sufficient for double paths.
The Aggreko board has rubber pads in the middle of the screws, which can effectively protect the plate against friction or fracturing.
Transparency is very good:
The back space is very large and the back line support is very friendly. The large opening of the motherboard position gives the radiator backplane enough free space to play
The thickness of the side plate is appropriate, the frame is strengthened, and the single hand-held side is not deformed
The height of the internal space is about 18cm. Therefore, the official support for 16cm heat dissipation is no water, and there is a margin of about 1cm.
At the time of installation, it was found that there was a silver gadget for the copper pillars.
Baffles are all removable, like one
The position of the cooling fan above the baffle is a large, long hole in the strip. The fan can be moved horizontally to meet different needs. This design is really good.
The power section was changed to an active baffle design to facilitate disassembly and assembly. This is a very good design. Personally think that there is a little bit of jealousy in the baffle and cabinet parts, with screw holes. It is awkward to screw on. Increase the opening of the baffle, which does not affect the activity, and it is more labor-saving when screwing up.
OK, start to introduce the installed components
120 water-cooled garbage 120G solid
500G Mechanical Antec Half Module
GTX950
South China factory X79 with 2680
4X4G memory
Installation will not repeat them, look directly at the finished product:
The back effect, because the back space is very large, so the soul line has no effect at all
The front is super refreshing
Because individuals do not like light pollution (have long been thought to get rid of the water-cooled fan lamp beads, have been too lazy, have not done), do not like noise, so what light chassis fan, etc. are completely absent, only from other aspects To evaluate:
MasterBox Lite 5 is a well-designed chassis with huge internal space and high transmissivity of the front and side panels. It is an excellent chassis installation experience: 9 points hardware architecture: 9 points expansion compatibility: 8 points Cost-effectiveness: 7 points on heat dissipation , Personally think that the direction of entering and exiting the chassis should be like this:
In order to see through the effect and appearance, the air intake opening of the chassis is somewhat small, and the individual feels that it is cooling. The chassis has made a certain sacrifice.
However, it does not hide, this chassis does show the atmosphere of the aesthetic effect, once again like it!
A flexible printed circuit board is a type of PCB designed to meet the needs of flexible electronic circuits. Originally designed flexible printed circuits to replace traditional wiring harnesses.
Flexible printed circuits are produced using flexible laminates. The flexible laminate holds the conductive foil as well as the dielectric substrate. Flexible circuit boards can be three-dimensionally routed and can be appropriately shaped to fit the available space.
Flexible PCB,Flexible Circuit Board,PCB Production Process,PCB Process Technology,Circuit Board Manufacturing Process
Huizhou Liandajin Electronic Co., Ltd , https://www.ldjpcb.com